Sig Sauer

Sig Sauer factory magazine catch for the Sig P938. Satin Nickel finish.

Sig Sauer P226R with the fast target capability of the ROMEO1 Reflex sight. The ROMEO1 Reflex Sight uses TruHold, a lockless system to maintain zero, and the MOTOAC (Motion Activated Illumination) system combined with co-witnessing suppressor height SIGLITE night sights for accurate hits round after round. Comes with suppressor height night sights, Romeo1 Reflex Sight, one-piece E2 grip panel, DA/SA trigger, 2 magazines, box, lock and manual.

Converts your P229 from .40S&W to 357SIG or replaces your original 357SIG barrel. These are factory Sig Sauer drop-in barrels.

* NOTE * All barrels may require minor fitting.

Sig Sauer P320 M17 Commemorative edition of the military contract sidearm. One of 5000 produced with serial numbers M17-0001 through M17-5000. Features coyote tan finish, ambi manual thumb safety, DP Pro Plate which allows you to install a Romeo red dot sight as well as the same coatings and markings of the military version. Comes with two 21RD and one 17RD magazines. After you register your pistol, you will receive a COA and a challenge coin from Sig Sauer. IOP

SIG factory Slide Catch Lever for all Sigpro models, 9mm, .40S&W and .357SIG.

The Sig Sauer SRD338Ti-QD Suppressor is a Grade 5 Titanium quick detach suppressor. The rear mount has wrench flats to torque the silencer to the barrel. There is a secondary retention latch that is depressed to remove the silencer from the mount. The SRD338Ti-QD is rated up to the 338 Lapua Mag and any other rifle cartridges that are of equal or less projectile diameter, pressure and case capacity. Examples of this would be .204 Ruger, .223/5.56x45mm, 5.45x39mm, 300 Win Mag, 7.62x39mm, 7.62x35 (300 Blackout), 6.5 Grendel, 6.5 Creedmoor, 6.8 Spc, .260 Remington and other cartridges. The SRD338Ti-QD comes with one M18x1.5mm Taper-Lok muzzle brake. Other muzzle devices are available.

-Length: 10.5x1.75 in.

-Weight: 18.9 ounces

-Threads: M18x1.5mm

-dB level - 138dB

The Sig Sauer SRD556-QD is a quick detach suppressor using inconel 718, a Nickel Alloy Stainless Steel, provides the highest level of durability, particularly with short-barreled hosts using supersonic ammunition. The rear mount has wrench flats to torque the silencer to the barrel. There is a secondary retention latch that is depressed to remove the silencer from the fast-attach mount. The SRD556-QD comes with one 1/2"x 28tpi Taper-Lok™ muzzle brake. Utilizes the popular 1/2"x 28tpi threads.

-Length: 6.5x1.625 in

-Weight: 14.0 ounces

-Threads: 1/2-28 tpi

-dB level - 134dB

The Sig Sauer SRD762 is a direct thread suppressor using inconel 718, a Nickel Alloy Stainless Steel, provides the highest level of durability, particularly with short-barreled hosts using supersonic ammunition. The rear mount has wrench flats to torque the silencer to the barrel. These wrench flats can be used as a location to "pin and weld" the silencer to make a shorter barrel over 16" in total length. The SRD762 is rated up to 300 Win Mag and any other rifle cartridges that are of equal or less projectile diameter, pressure and case capacity. Examples of this would be .204 Ruger, .223/5.56x45mm, 5.45x39mm, 7.62x39mm, 7.62x35 (300 Blackout) 6.5 Grendel, 6.5 Creedmoor, 6.8 Spc, .260 Remington and other cartridges. Utilizes the popular 5/8"-24tpi threads.

-Length: 6.6x1.625 in.

-Weight: 15.5 ounces

-Threads: 5/8"-24 tpi

-dB level - 139dB

The Sig Sauer X-RAY3 Night Sights are rugged, all steel sights for duty, carry, or sporting pistols. This 3 dot tritium night sight set features a blacked out rear with green high visibility front sight for intuitive front sight acquisition day or night. Ideal for duty and defensive pistols where a quick front sight picture is advantageous. Available with U-notch or traditional square rear sight picture. Green/Green. Fits Classic P-Series, P320, P250, P938 and P238.

The Sig Sauer X-RAY3 Night Sights are rugged, all steel sights for duty, carry, or sporting pistols. This 3 dot tritium night sight set features a blacked out rear with green high visibility front sight for intuitive front sight acquisition day or night. Ideal for duty and defensive pistols where a quick front sight picture is advantageous. Available with U-notch or traditional square rear sight picture. Green/Green. Fits Classic P-Series, P320, P250, P938 and P238.

SIG factory Standard Nickel Trigger for older production P220 and P245 models with the narrow trigger, 8mm. Will not fit current produced P220's with 10mm trigger.

Sig Sauer factory Hammer Strut for P220 models. Will not fit older spurred hammers. E2 grip kit hammer strut.

SIG SAUER P250 10RD magazines chambered in 9mm. High quality steel construction and finished with an advanced anti-friction coating. These are reduced capacity for those in restricted areas. This magazine will only fit P250's with the original grip style. To determine which style P250 Compact you own, please see the P250 Compact Grip Change reference sheet.

Factory Sig Sauer P250 Grip Module allows the shooter to tailor the pistol to meet their specific grip size requirements. Black polymer construction and comes with the magazine catch installed. This is the large grip for the .45ACP P250 Full Size.

*Note: These are the updated Grip Modules which includes a replacement new style slide catch lever, slide catch lever spring, and slide catch post.

* NOTE * All barrels may require minor fitting.

Sig Sauer push button quick detach sling swivel designed for any sling mount, stock or other accessory with QD socket capability.

Sig Sauer ALUMINUM factory Short Trigger for SIGPRO models.