GRAYGUNS PARTS

GRAYGUNS PARTS

Products

Grayguns Master Spring Set - Sig Sauer P-Series - NOT P225/P6

Grayguns Master Spring Set - Sig Sauer P-Series - NOT P225/P6

From Grayguns, a Master Spring Set for Sig Sauer P-Series handguns. The P-MSS kit is an action upgrade package designed to reduce trigger pull weight while still providing reliable primer strikes. This set includes two mainsprings, one 17 lb. and one 19 lb., and a competition sear spring.

Fits the modern P-Series handguns with a DA/SA system, P220, P224, P225A1, P226, P227, P228, P229 and P-226 X-Five Allround.

SYS-SIG-22X-MSS

In stock

$16.00

Grayguns Pink+P9 Heavy Duty Recoil Spring

Grayguns Pink+P9 Heavy Duty Recoil Spring

Grayguns Pink+P9 recoil spring for Sig Sauer pistols. A heavy duty P226 9mm spring for those shooting hot 9mm loads.


Also suitable to P226 .40/357 and the P220 .45ACP if using reduced power loads.

SPR-SIG-226-HDU

In stock

$10.00

Grayguns Classic Standard Curved Trigger - Sig Sauer P-Series

Grayguns Classic Standard Curved Trigger - Sig Sauer P-Series

The P22xCT Classic Standard Trigger adds over-travel adjustability to our original design. Utterly indestructible, the P22xCT Classic Standard is machined from tough steel, carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function.

Our intermediate trigger shape optimizes both SA and DA control for optimal control, and is more comfortable than the factory short trigger it replaces. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

Will not fit SIG Pro, X5 Allround, P225 / P6, P239 or most SAO models. Also will not fit older P220 with 8mm wide trigger.

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

This product was previously referred to as the P-Series Precision Adjustable Intermediate Trigger (P-SAIT).

TRG-SIG-22X-AIC

In stock

$39.00

Grayguns Fat Guide Rod - Sig P220/P226 - Super Black

Grayguns Fat Guide Rod - Sig P220/P226 - Super Black

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P220 and P226 - Super Black Finish

GRD-SIG-22F-SB

In stock

$25.00

Grayguns P320 Adjustable Hybrid Trigger

Grayguns P320 Adjustable Hybrid Trigger

Bruce Gray combined the best of both worlds when he designed what we know as the hybrid trigger.

The unique face allows the shooter can take advantage of finger placement lower on the face, with the comfort of a traditional curved face. This hybrid design reduces trigger weight while preserving all mechanical safety values.

The Grayguns P320 Hybrid Trigger uses internal leverage changes to yield superior trigger pull, while supporting the voluntary upgrade’s enhanced reliability and rough handling performance qualities.

Includes our adjustable over-travel stop design to shorten reset and take out all gross over-travel. Designed for easy drop-in installation.

Specifically designed for P320s with current fire control unit components, or those who have gone through SIG’s Voluntary Upgrade Program.

Specifications and Features

  • Specifically designed for P320s with current fire control unit components, or those who have gone through SIG’s Voluntary Upgrade Program
  • Adjustable over-travel to help reduce reset and take out wasted motion
  • Reduces total trigger pull weight approximately 2 pounds below factory-stock for the standard series, and about 1.25 pounds for the X-Five variant
  • Designed for use with the SIG factory trigger bar spring
  • Minimal over-travel, stops at optimum trigger face angle
  • Smoother takeup and release sensation
  • Preserves factory sear engagement and mechanical safety values
  • Proven reliable and durable for high-volume professional use
  • Limited lifetime warranty on materials and workmanship

Fit Guide

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five and RX versions.

Disclaimer

These parts are intended for installation by a qualified armourer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action. This is due to the varying tolerances present in all mass-produced firearms. Although kits fit with no issues in a great majority of pistols, Grayguns is unable to guarantee perfect functionality in every instance. Grayguns does offer installation services for all parts kits we offer.

TRG-SIG-320-AHT

In stock

$89.00

Grayguns Competition Adjustable Straight Trigger Kit - Sig Sauer P320

Grayguns Competition Adjustable Straight Trigger Kit - Sig Sauer P320

The new Grayguns P320 Adjustable Straight Competition Trigger System delivers the unequalled smooth feel and hot performance of our custom action work in a cleverly engineered drop-in kit.

Paired with Bruce Gray’s exclusive straight trigger design, this is the most advanced drop in competition system available for all post/Voluntary Upgrade P320 models.

The P320 Competition Adjustable Straight Trigger System is intended for installation by an armorer, gunsmith or skilled individual who is familiar with the P320 fire control unit.

The kit includes the following exclusive Grayguns elements:

  • Our newly designed straight trigger with built in over-travel adjustment
  • Precision-ground custom sear, polished and finished in hard nickel PTFE. Specifically designed for competition or range use only.
  • Grayguns original competition sear springs
  • Intermediate competition sear springs
  • Original soft competition trigger bar spring
  • New snappy-reset trigger bar spring
  • Micro-polished, extended safety lever pin

Fit Guide

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five, Legion and RX versions.

Disclaimer

These parts are intended for installation by a qualified armourer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action. This is due to the varying tolerances present in all mass-produced firearms. Although kits fit with no issues in a great majority of pistols, Grayguns is unable to guarantee perfect functionality in every instance. Grayguns does offer installation services for all parts kits we offer. Note – The safety lever spring is no longer needed in the P320, and is not included in the kit.

SYS-SIG-320-AST

In stock

$149.00

Grayguns Fat Guide Rod - Sig P320 Full Size - Stainless

Grayguns Fat Guide Rod - Sig P320 Full Size - Stainless

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P320 Full size - Stainless W/15lb 1911 Recoil Spring

GRD-SIG-320-ST

In stock

$25.00

Grayguns Sig Sauer P320 Hard Duty Use Trigger - Curved

Grayguns Sig Sauer P320 Hard Duty Use Trigger - Curved

The Grayguns P320ST and P320CT triggers are specifically designed for guns that have gone through SIG Sauer’s® Voluntary Upgrade Program. The trigger is available in your choice of straight-face or curved-face design.

The Grayguns P320 trigger yields superior trigger pull results while supporting the voluntary upgrade’s enhanced reliability and rough handling performance qualities. It is designed for drop-in installation.

P320 Trigger – Straight or Curved – Specifications and Features

  • Specifically intended for use only in P320s that have gone through SIG’s Voluntary Upgrade Program.
  • Reduces total trigger pull weight approximately 2 pounds below factory-stock for the standard series, and about 1.25 pounds for the X-Five variant.
  • Designed for use with the SIG factory trigger bar spring
  • Minimal over-travel, stops at optimum trigger face angle
  • Smoother takeup and release sensation
  • Preserves factory sear engagement and mechanical safety values
  • Proven reliable and durable for high-volume professional use
  • Our triggers are externally comparable in appearance to the factory part
  • Limited lifetime warranty on materials and workmanship

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five and RX versions.

This trigger was previously described as our Practical Enhanced Leverage Trigger (PELT).


TRG-SIG-320-CT

In stock

$89.00

Grayguns Competition Hybrid Trigger Kit - Sig Sauer P320

Grayguns Competition Hybrid Trigger Kit - Sig Sauer P320

The new Grayguns P320 Competition Trigger System delivers the unequalled smooth feel and hot performance of our custom action work in a cleverly engineered drop-in kit.

Paired with Bruce Gray’s exclusive hybrid trigger design, this is the most advanced drop in competition system available for all post/Voluntary Upgrade P320 models.

The P320 Competition Trigger System is intended for installation by an armorer, gunsmith or skilled individual who is familiar with the P320 fire control unit.

The kit includes the following exclusive Grayguns elements:

  • Our newly designed hybrid trigger with built in over-travel adjustment
  • Precision-ground custom sear, polished and finished in hard nickel PTFE. Specifically designed for competition or range use only.
  • Grayguns original competition sear springs
  • Intermediate competition sear springs
  • Original soft competition trigger bar spring
  • New snappy-reset trigger bar spring
  • Micro-polished, extended safety lever pin

Specifications and Features

  • Specifically intended for use only in P320s that have gone through SIG’s Voluntary Upgrade Program.
  • Reduces trigger pull weight to suit your preferences, with additional springs provided to yield custom pull weights.
  • Adjustable over-travel, stops at optimum trigger face angle
  • Smoother takeup and clean release sensation, with clean reset
  • Preserves factory sear face engagement height and mechanical safety values
  • Proven reliable and durable for high-volume professional use
  • Limited lifetime warranty on materials and workmanship

Fit Guide

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five and RX versions.

Disclaimer

These parts are intended for installation by a qualified armourer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action. This is due to the varying tolerances present in all mass-produced firearms. Although kits fit with no issues in a great majority of pistols, Grayguns is unable to guarantee perfect functionality in every instance. Grayguns does offer installation services for all parts kits we offer. Note – The safety lever spring is no longer needed in the P320, and is not included in the kit.

SYS-SIG-320-AHT

In stock

$149.00

Grayguns Dual Adjustable Straight Trigger - Sig Sauer P-Series - STEEL BLACK

Grayguns Dual Adjustable Straight Trigger - Sig Sauer P-Series - STEEL BLACK

The SIG P-Series Dual Adjustable Straight Trigger is the straight-faced version of our legendary curved P-Series Dual Adjustable Trigger. This trigger includes over travel and pre-travel adjustability. (Adjustable for double action slack and single action over travel.)

The optimized trigger face pressure-wall angle provides for outstanding single action sear release and positive, ultra-fast reset control. The ergonomics provides superior double action leverage and control.

Dual Adjustable Straight Trigger Details

This trigger is machined from tough steel. The trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

The trigger weight is about .83 ounces (23.45 grams)

Fit Guide

The trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including

  • X5 All-Round
  • P220 (see exceptions below)
  • P226
  • P228
  • P229
  • P227 and others

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

TRG-SIG-22X-DAS

In stock

$69.00

Grayguns HK P30 w/Safety Short Reset System

Grayguns HK P30 w/Safety Short Reset System

Replicate our custom in-house short reset conversion with a drop-in kit for your HK P30 with thumb safety. Cut from bar stock steel, these kits provide an exacting fit for easy install.

The kit shortens the reset travel distance by about one-third, reduces trigger over-travel and reduces pull weight while maintaining all factory safety functions.

This kit is specific to the HK P30 model with a thumb safety, including DA/SA and LEM variations.

The kit works with all variants of the HK P30 with a thumb safety including:

  • P30
  • P30L
  • P30SK

Will not work with CDA LEM 4.1 trigger.

The parts provided – control latch, extended sear roll pin and firing pin block spring – are designed to be installed together as a complete system.

SYS-HK-P30-MS

In stock

$85.00

Grayguns HK USP, HK45 Short Reset System

Grayguns HK USP, HK45 Short Reset System

Our Short Reset System for the HK USP and HK45 replicates the short reset conversion available in our in-house custom action work. Cut from bar stock steel, these kits provide an exacting fit for easy install.

The kit shortens the reset travel distance by about one-third, reduces trigger over-travel and reduces pull weight while maintaining all factory safety functions.

This kit is specific to the HK USP and HK45 models with or without a thumb safety, including DA/SA and LEM variations.

The parts provided – control catch, pin and spring – are designed to be installed together as a complete system.

Kits will not fit the following variants:

  • Double Action Only pistols
  • MK23
  • Early USP models with joined one piece catch, control latch or models that have the short catch that stops the hammer rather than spur. These older versions are rare and usually easily identified because they lack the rubber coating on the hammer thumb stud.

SYS-HK-USP-STD

In stock

$85.00

Grayguns Dual Adjustable Curved Trigger - Sig Sauer P-Series - STEEL BLACK

Grayguns Dual Adjustable Curved Trigger - Sig Sauer P-Series - STEEL BLACK

The Grayguns P-Series Dual Adjustable Curved Trigger is the ultimate trigger upgrade for your Legion Series or any modern DA/SA SIG P-Series pistol.

Bruce Gray has combined the adjustable over-travel feature, unbeatable comfort and control and unrivaled quality of our original OEM SIG Sauer® Legion P22xCT, Classic Standard trigger, with the improved geometry and pre-travel adjustment of our wildly popular P22xST Dual Adjustable Straight Trigger series.

This trigger is the ultimate upgrade for your Legion Series or any modern DA/SA SIG P-Series pistol.

Our Dual Adjustable Curved Trigger

This steel trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. The trigger is guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

Fit Guide

The Dual Adjustable Curved Trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including:

  • X5 All-Round
  • P220 (see exception below)
  • P226
  • P228
  • P229
  • P227, and others.

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-Series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width.

TRG-SIG-22X-DAC

In stock

$69.00

Grayguns Hard Duty Use P320 Magazine Base Pad - Extended

Grayguns Hard Duty Use P320 Magazine Base Pad - Extended

Designed for hard-duty use. Our custom Grayguns SIG Sauer P320 magazine base pads are manufactured from 6061 Aluminum. Professionally finished with MIL-A-8625 Type III anodized coating. Pads go through a glass-beading process to provide a flat-black finish.

The base pad is the same thickness as the OEM SIG base pad. A relief cut on the sides enhances malfunction drills, and allows for effective one-handed reloads using the belt or holster.

The cut mirrors the normal P320 module’s and creates a cut for the X-Series modules.

Each pad features a 3-by-5 matrix. Number your mags using a Sharpie or paint pen. Additional space is available to write your initials.

Backwards compatible with all versions of P320 modules, including the standard and X-Series with or without the extended magwell installed.

  • This the Extended Version Designed for the full-size magazine in a XSeries with the magwell. Also works with 21-round magazines and fits the standard P320.

Note: These base pads are compatible with new SIG P320 magazines with the square pegs.

BPD-SIG-32X-HDE

In stock

$19.99

Grayguns Sig Sauer P320 Hard Duty Use Trigger -  Adjustable Straight

Grayguns Sig Sauer P320 Hard Duty Use Trigger - Adjustable Straight

The Grayguns P320 Adjustable Straight Trigger is the ultimate fire control refinement for this amazingly versatile platform, embodying the best innovations from Bruce Gray’s continuing R&D program with SIG Sauer®. Like all Grayguns Inc. products, proudly American made from precision machined tool steel, heat treated, hand finished and gauged for perfect appearance, fit and function.

Designed for hard duty use, with the toughness to outlast your pistol, our P320 triggers are Grayguns Grade and guaranteed for life.

P320 Trigger – Straight or Curved – Specifications and Features

  • Adjustable over-travel eliminates gross movement after the sear is released, and reduces trigger travel to reset
  • Enhanced Leverage geometry reduces pull weight by 30% with stock springs
  • Smoother takeup, sear release and reset sensation
  • Optimal 90⁰ sear release
  • Supports Voluntary Upgrade rough handling characteristics for assurance and reliability

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five and RX versions.

This trigger was previously described as our Practical Enhanced Leverage Trigger (PELT).


TRG-SIG-320-AST

In stock

$89.00

Grayguns Fat Custom Strut System - Sig Sauer P Series

Grayguns Fat Custom Strut System - Sig Sauer P Series

The Grayguns custom-designed Strut System fully supports the main spring, reducing friction, spring bowing and fatigue. The design eliminates the typical double action “crunch” felt in OEM pistols. This full system also includes our custom P-Series Master Spring Set, to help reduce your pull weight for full tuning options.

The SIG P-Series Fat Custom Strut System was designed by Bruce Gray to help bring another Grayguns custom gunsmithing service to the drop in parts market.

For more than 40 years Bruce has been modifying factory struts to eliminate the typical double action crunch caused by the sharp edges and tip of the strut.

In his new design, the fat strut fully supports the main spring which reduces friction, spring bowing, and fatigue. The struts are cut using a precision EDM process, hand finished, and heat treated to the proper hardness. Paired with the upgraded strut, is a durable seat machined in-house out of aircraft grade aluminum and anodized. These struts are indestructible and guaranteed for life.

This full system also includes our custom P-Series Master Spring Set, to help reduce your pull weight for full tuning options. Includes 17 pound spring (red) and 19 pound spring (blue).

Fit Guide

The system is compatible with the E2 style grips, as well as most older style grips. The system fits most of the following SIG DA/SA pistol variants:

  • P226
  • P228
  • P229
  • P225-A
  • P227

Disclaimer

These parts are intended for installation by a qualified armorer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action.

SYS-SIG-226-STRUT

In stock

$69.00

Grayguns Fat Guide Rod - Sig P228/P229 - Stainless

Grayguns Fat Guide Rod - Sig P228/P229 - Stainless

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P228 and P229 - Stainless

GRD-SIG-22C-SS

In stock

$20.00

Grayguns Hard Duty Use VP9/P30 Magazine Base Pad - Standard Brass

Grayguns Hard Duty Use VP9/P30 Magazine Base Pad - Standard Brass

Brass Base Pads are perfect for competitors looking to add weight to their pistol. As compared to our 6061 Aluminum pads with anodized coating for the P320, P226 or VP9/P30 the Brass Base Pads are significantly heavier; more than triple the weight.

For USPSA Production, ensure you weigh your setup to ensure you are under the maximum weight limit.

Each pad features a 3-by-5 matrix. Number your mags using a Sharpie or paint pen. Additional space is available to write your initials.

Weight Comparison – VP9 & P30

  • Brass (VP9/P30) – 1 ounce
  • Grayguns Hard Duty Use Aluminum Pads (VP9/P30) – About .3 ounces

A spacer – shown in photos – is included for use with 15-round magazines. No spacer is required for the 17-round magazines.

BPD-HK-P30-HDS-BRASS

In stock

$26.95

Grayguns Gun Parts

Grayguns gun parts by renown pistolsmith and Grand Master competition shooter, Bruce Gray. Bruce and his team of highly skilled craftsmen have developed high quality upgrades for Sig Sauer pistols from solid guide rods, sights, recoil springs, extractors, triggers to drop in action enhancement kits. Grayguns offers leading edge design and engineering for the shooter that needs the highest performance out of their pistols. Take your Sig Sauer to the next level with superior products from Grayguns, Inc. On top of creating an end user parts supply, Grayguns is a full service gunsmithing custom shop providing modifications that are well beyond the scope of dropping in parts. OpSpec Training is another branch of the business that provides serious training to new shooters as well as advanced classes for law enforcement, competition shooters and those who want "up their game" for self defense purposes. Top Gun Supply is not only a vendor of Grayguns. We are also a customer and have used most of Bruce's services. But, don't take our word. Ask any one of the many, many satisfied customers.