Aero Precision

Precision machined to accept standard .308 components and forged from 7075-T6 aluminum, the Aero Precision M5 upper is the ideal fit for your next big bore build.

Features:

• M4 Feedramps
• .2795 takedown pin holes (DPMS size)
• Lazer engraved T-marks
• DPMS High Profile (.210) Tang

Includes:

• M5 (.308) Lower Receiver
• A2 Grip
• M4 Stock
• Mil-Spec Lower Parts Kit
• 308 Carbine Buffer and Spring
• These parts are installed

Includes:

• M5 (.308) Lower Receiver
• Magpul MOE Grip
• No Stock
• Lower Parts Kit
• M5 Carbine Buffer and Spring
• These parts are installed

M5 (.308) lower parts kit helps you to build a custom .308 AR from the ground up. Mil- spec dimensions and coating ensure the highest quality and correct component interface.

Includes:

• Takedown/pivot Spring
• Takedown/pivot detent
• M5 .308 Takedown pin
• M5 .308 Pivot pin
• M5 .308 Bolt Catch
• Bolt Catch Spring
• Bolt Catch Buffer
• Bolt Catch Roll pin
• Safety Selector
• Safety Selector Spring
• Safety Selector Detent
• Buffer Retainer
• Buffer Retainer Spring
• Magazine Catch Body
• Magazine Catch Spring
• Extended Magazine Catch Button

Our M5 .308 Stripped Lower Receiver helps you build a big-bore AR from the ground up. Mil-spec dimensions and coating ensure the highest quality and correct component interface. DPMS cut.

Features:

• Works with standard AR 308 components and magazines
• Upper Tension Screw - Allows users to fine tune the fit of the upper and lower receiver through the use of a nylon tipped tensioning set screw inserted in the grip tang of the lower receiver.
• Rear takedown pin detent hole is threaded for a 4-40 set screw
• Bolt catch is threaded for a screw pin (no roll pin needed)
• Integrated trigger guard
• Selector markings will work with 45, 60 or 90 degree safety selectors
• Accepts Battle Arms Development short throw safety selectors, but will work with any standard selector
• No gap with aftermarket pistol grips

Includes:

• Stripped M5 (.308) Lower Receiver in Anodized Black
• Nylon tipped tensioning set screw

• Ultralight 1" Extended Scope Mount features a rear ring that is pushed forward 1", resulting in better eye relief
• Designed for AR type Upper Receivers
• Fits Mil-Spec 1913 Picatinny Rails
• Cross-Slot Keyway
• 6061-T6 Aluminum Construction
• Black Hard Coat Anodized
• Free from unnecessary bulk, providing one of the lightest mounts in the industry

• Designed for AR type Upper Receivers
• Fits Mil-Spec 1913 Picatinny Rails
• Cross-Slot Keyway
• 6061-T6 Aluminum Construction
• Black Hard Coat Anodized
• Free from unnecessary bulk, providing one of the lightest mounts in the industry

The Aero Precision VG6 EPSILON 556 is the pinnacle of AR15 muzzle devices. Utilizing many of the same muzzle brake/compensating features as the GAMMA 556, the EPSILON 556 also includes additional flash hiding characteristics. Extended flash hiding prongs and no ports at the 12 o’clock positions allow uninhibited view from flash through optics or sights. Updated chamber design features improved gas flow and rigidity. By leveraging modern design principles both functionally and aesthetically, we continue to keep the VG6 product family at the cutting edge of muzzle device performance.

Features:

• Material: 17-4ph® Heat Treated Stainless Steel
• Finish: BLACKNITRIDE™
• Surface Hardness: 68RC
• Caliber: 5.56mm/.223 Rem. only
• Thread: 1/2-28 RH
• Weight: 2.5oz
• Includes crush washer

The VG6 EPSILON AK is the pinnacle of AK47 muzzle devices. The EPSILON AK just outperforms everything on the market.

Designed for the discriminating shooter and professional end-users, VG6 Precision's EPSILON AK affords you the best muzzle control and recoil mitigation the industry has to offer. This is a true combination muzzle brake / compensator / flash hider. Its performance is matched only by the amazing look of this device.

The VG6 Epsilon AK carries many of the same characteristics as the Gamma line of muzzle brakes with a few exceptions. Extended flash hiding prongs allow uninhibited view from flash through optics or sights. The difference in porting is noticed on the underside of the device where it has 6 valve holes to allow the fastest gasses reaching the second chamber to exit. This creates very soft low energy recoil that allows for absolute control.

Features:

• Material: 17-4ph® Heat Treated Stainless Steel
• Finish: BLACKNITRIDE™
• Surface Hardness: 68RC
• Caliber: 7.62 x 39mm Only
• Thread: 14x1.0 LH
• Weight: 2.24oz
• Indexing pin slot for standard AK47 muzzle device retention
• Includes crush washer (not needed if using indexing pin)

The Gamma 556SL is the perfect muzzle device for your pinned and welded builds. The Gamma 556SL is long enough to provide an overall length of 16" when permanently affixed to the barrel. Its outside diameter of .745 inches allows you to install and service your gas system without removing the muzzle brake. The 3-chamber design looks great on any standard profile barrel while effectively eliminating recoil leaving your rifle shooting flat and soft.

The VG6 GAMMA 762 is a high-performance muzzle brake for eliminating recoil. It was designed using state of the art engineering techniques, utilizing CFD (Computational Fluid Dynamics) and CAE (Computer Aided Engineering). This product is 100% CNC machined for optimal performance.

The GAMMA 762 is a muzzle brake and compensator hybrid that virtually eliminates recoil and muzzle movement during firing. The unique combination of both muzzle brake and compensator functionality inspires shooter confidence and allows for quicker follow up shots.

Optimized for use with full power rifle cartridges, the GAMMA 762 is the perfect choice for taming the recoil on everything from AR308s to your favorite bolt action rifle.

Updated chamber design features improved gas flow and rigidity. By leveraging modern design principles both functionally and aesthetically, we continue to keep the VG6 product family at the cutting edge of muzzle device performance.

Aero Precision Mil-Spec carbine buffer for use in AR15 carbines with a collapsible buttstock. Perfect for your build or direct replacement for worn out parts. Made in the USA.

Features:

• Aluminum Alloy Standard Charging Handle
• Black Anodized
• Caliber - .308
• Made in the USA

• Used behind flash hider on your AR15
• Phosphate coated
• Made in the USA

Upper Receiver Features:

• Machined from 7075-T6 forged aluminum
• Coating:FDE Cerakote finish
• M4 Feedramps
• .250” takedown pin holes
• Accepts standard AR15/M16 components

Lower Receiver Features:

• Machined from 7075-T6 forged aluminum
• Coating:Magpul™ FDE Cerakote finish
• Works with standard AR15 components and magazines
• Rear takedown pin detent hole is threaded for a 4-40 set screw

• Mil-Spec 7075-T6 Aluminum Buffer Tube, 6-position
• .308 carbine buffer
• .308 buffer spring
• End plate and lock nut
• Made in the USA

*STOCK NOT INCLUDED*

Features:

• Front and rear picatinny rail
• Eliminated center of top rail for weight reduction
• Indexing grooves in 12:00 position for positive grip control
• Quick disconnect sling socket at the 3, 6 and 9 o’clock positions
• Compatible with low profile gas blocks
• 1.3” Inside diameter
• 1.5” Outside diameter
• Compatible with mil-spec AR15 upper receivers and barrels