Aero Precision

The M4E1 upper receiver is a one-piece design combining the handguard mounting platform with the upper itself. Through superior engineering, we have condensed the parts needed to mount a free-floated handguard to a mere 8 screws. Since the handguard mounting surface and upper are of the same forging, not only is it a stronger system, but we are able to make additional lightening cuts to save weight and allow for more efficient cooling.

Ease of installation - Simply insert your barrel assembly into the M4E1 upper, tighten it using the provided barrel nut and wrench, slide your rail on and tighten the rail screws. Within minutes you have a modular, free-floated rail.

Features:

• M4 Feedramps
• .250 takedown pin holes
• Lazer engraved T-marks
• Comes assembled, with dust cover and forward assist installed

M4E1 Specific Details:

• Handguard mounting platform is forged into the receiver
• Compatible with Aero Precision Enhanced and Quantum Series handguards but also fits most BAR-system handguards
• Barrel nut and wrench are included
• These uppers are not piston-kit compatible
• Will support barrels with a diameter up to 1"

Includes:

• AR15 M4E1 Upper Receiver in Anodized Black
• Port Door and Forward Assist installed
• Barrel nut
• Barrel nut wrench

Precision machined to accept standard .308 components and forged from 7075-T6 aluminum, the Aero Precision M5 upper is the ideal fit for your next big bore build.

Features:

• M4 Feedramps
• .2795 takedown pin holes (DPMS size)
• Lazer engraved T-marks
• DPMS High Profile (.210) Tang

Includes:

• M5 (.308) Lower Receiver
• A2 Grip
• M4 Stock
• Mil-Spec Lower Parts Kit
• 308 Carbine Buffer and Spring
• These parts are installed

Includes:

• M5 (.308) Lower Receiver
• Magpul MOE Grip
• No Stock
• Lower Parts Kit
• M5 Carbine Buffer and Spring
• These parts are installed

M5 (.308) lower parts kit helps you to build a custom .308 AR from the ground up. Mil- spec dimensions and coating ensure the highest quality and correct component interface.

Includes:

• Takedown/pivot Spring
• Takedown/pivot detent
• M5 .308 Takedown pin
• M5 .308 Pivot pin
• M5 .308 Bolt Catch
• Bolt Catch Spring
• Bolt Catch Buffer
• Bolt Catch Roll pin
• Safety Selector
• Safety Selector Spring
• Safety Selector Detent
• Buffer Retainer
• Buffer Retainer Spring
• Magazine Catch Body
• Magazine Catch Spring
• Extended Magazine Catch Button

Our M5 .308 Stripped Lower Receiver helps you build a big-bore AR from the ground up. Mil-spec dimensions and coating ensure the highest quality and correct component interface. DPMS cut.

Features:

• Works with standard AR 308 components and magazines
• Upper Tension Screw - Allows users to fine tune the fit of the upper and lower receiver through the use of a nylon tipped tensioning set screw inserted in the grip tang of the lower receiver.
• Rear takedown pin detent hole is threaded for a 4-40 set screw
• Bolt catch is threaded for a screw pin (no roll pin needed)
• Integrated trigger guard
• Selector markings will work with 45, 60 or 90 degree safety selectors
• Accepts Battle Arms Development short throw safety selectors, but will work with any standard selector
• No gap with aftermarket pistol grips

Includes:

• Stripped M5 (.308) Lower Receiver in Anodized Black
• Nylon tipped tensioning set screw

• Ultralight 1" Extended Scope Mount features a rear ring that is pushed forward 1", resulting in better eye relief
• Designed for AR type Upper Receivers
• Fits Mil-Spec 1913 Picatinny Rails
• Cross-Slot Keyway
• 6061-T6 Aluminum Construction
• Black Hard Coat Anodized
• Free from unnecessary bulk, providing one of the lightest mounts in the industry

• Designed for AR type Upper Receivers
• Fits Mil-Spec 1913 Picatinny Rails
• Cross-Slot Keyway
• 6061-T6 Aluminum Construction
• Black Hard Coat Anodized
• Free from unnecessary bulk, providing one of the lightest mounts in the industry

The VG6 EPSILON AK is the pinnacle of AK47 muzzle devices. The EPSILON AK just outperforms everything on the market.

Designed for the discriminating shooter and professional end-users, VG6 Precision's EPSILON AK affords you the best muzzle control and recoil mitigation the industry has to offer. This is a true combination muzzle brake / compensator / flash hider. Its performance is matched only by the amazing look of this device.

The VG6 Epsilon AK carries many of the same characteristics as the Gamma line of muzzle brakes with a few exceptions. Extended flash hiding prongs allow uninhibited view from flash through optics or sights. The difference in porting is noticed on the underside of the device where it has 6 valve holes to allow the fastest gasses reaching the second chamber to exit. This creates very soft low energy recoil that allows for absolute control.

Features:

• Material: 17-4ph® Heat Treated Stainless Steel
• Finish: BLACKNITRIDE™
• Surface Hardness: 68RC
• Caliber: 7.62 x 39mm Only
• Thread: 14x1.0 LH
• Weight: 2.24oz
• Indexing pin slot for standard AK47 muzzle device retention
• Includes crush washer (not needed if using indexing pin)

Features:

• Front and rear picatinny rail
• Eliminated center of top rail for weight reduction
• Indexing grooves in 12:00 position for positive grip control
• Quick disconnect sling socket at the 3, 6 and 9 o’clock positions
• Compatible with low profile gas blocks
• 1.3” Inside diameter
• 1.5” Outside diameter
• Compatible with mil-spec AR15 upper receivers and barrels

Features:

• Aluminum Alloy Standard Charging Handle
• Black Anodized
• Caliber - .308
• Made in the USA

• Machined from 8620 Tool Steel (Carrier) and 9310 Steel (Bolt)
• Carrier has forward assist serrations
• Shrouded firing pin
• Nickel Boron Coating inside and out (Bolt, Carrier, and Gas Key)
• Forged Mil-Spec gas key attached with Grade 8 hardware and Properly staked.
• 5.56 Bolt is shot Peened and MPI
• Mil-Spec Extractor Spring, black extractor insert, Viton O-Ring
• Tool Steel Extractor
• High quality BCG

The AR15 Assembled Upper Receiver comes with the port door and forward assist already installed. Forged from 7075-T6 aluminum, this assembled upper is precision machined to mil- spec M16/M4 specifications and features M4 feedramps. Match this upper with one of our AR15 lower receivers for a solid and dependable fit.

Features:

• M4 Feedramps
• .250 takedown pin holes
• Port door and forward assist installed

Includes:

• AR15 Assembled Upper Receiver in OD Cerakote H-232Q

The new Aero Taper Lock Attachment System (ATLAS) is both functional and aesthetically pleasing. It features 2 mirrored tapered locking nuts that provide evenly distributed clamping pressure across a custom engineered barrel nut with use of a turnbuckle screw. A ratcheting detent further secures the design while providing positive registration during installation. By design, the even pressure of the ATLAS system avoids distortion of the handguard often seen with current applications during installation.

All hardware mounting parts are included with the purchase of an ATLAS Handguard.

Aero Precsion AR15 Stripped Lower Receiver is the perfect base for your custom AR15 build. Machined to mil-spec dimensions, their lowers work with standard AR15 components and ensure the highest quality with a correct component interface.

Includes:

• Stripped AR15 Gen 2 Lower Receiver in OD Cerakote H-232Q
• Nylon tipped tensioning screw
• Billet Trigger Guard - OD Green

The Aero Precision BREACH® is a rugged, ambidextrous, precision-manufactured charging handle for the AR15 platform. The BREACH's design utilizes a reinforced 7075-T6 aluminum bar that is up to the most demanding tasks. Its ambidextrous levers feature a patent-pending, dual spring system, that directs the force-of-use into the robust charging handle body. This allows the shooter to use a one-sided charging technique without compromising the part — a pitfall for traditional mil-spec charging handles.

The small lever configuration provides a low-profile, easily gripped interface that is comfortable when slung and can be actuated effortlessly from either side of your rifle.

• Ambidextrous Controls: Ergonomically designed 7075 Aluminum levers allow the user to easily charge their firearm with either hand, while remaining low profile and comfortable when slung.
• Robust Construction: Reduced chamfer angles on the 7075 Aluminum reinforced bar design provide a strong foundation for the BREACH® that is resistant to rotational flex or breakage.
• Patent-pending Lever Mechanism: Transfers force-of-use away from the roll pins and into the top/head portion of the reinforced bar protecting the charging handle in the most demanding circumstances.
• Gas Deflection Shelf: Aligns with the upper receiver to redirect gas flow away from the users face when shooting suppressed.
• Functional Design: It is not all just good looks. Stylistic cuts on the charging handle also help to clear stuck on carbon and debris from the upper receiver, while the spacer design seals and protects the lever mechanism from debris.