Sig Sauer factory Firing Pin Retaining Pin for P227, P220, P226, P229, P229. P224 and P239 stainless steel slide models. This is the spiral or coiled pin found on later model pistols. Not for use on older pistols or those that use the solid FPPP or the 2 piece roll pins. For slides with short extractors only.

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P220 and P226 - Super Black Finish

Sig Sauer factory Safety Lock Spring for P220, P225, P226, P228 and P245 models with carbon steel slides.

Bruce Gray combined the best of both worlds when he designed what we know as the hybrid trigger.

The unique face allows the shooter can take advantage of finger placement lower on the face, with the comfort of a traditional curved face. This hybrid design reduces trigger weight while preserving all mechanical safety values.

The Grayguns P320 Hybrid Trigger uses internal leverage changes to yield superior trigger pull, while supporting the voluntary upgrade’s enhanced reliability and rough handling performance qualities.

Includes our adjustable over-travel stop design to shorten reset and take out all gross over-travel. Designed for easy drop-in installation.

Specifically designed for P320s with current fire control unit components, or those who have gone through SIG’s Voluntary Upgrade Program.

Specifications and Features

• Specifically designed for P320s with current fire control unit components, or those who have gone through SIG’s Voluntary Upgrade Program
• Adjustable over-travel to help reduce reset and take out wasted motion
• Reduces total trigger pull weight approximately 2 pounds below factory-stock for the standard series, and about 1.25 pounds for the X-Five variant
• Designed for use with the SIG factory trigger bar spring
• Minimal over-travel, stops at optimum trigger face angle
• Smoother takeup and release sensation
• Preserves factory sear engagement and mechanical safety values
• Proven reliable and durable for high-volume professional use
• Limited lifetime warranty on materials and workmanship

Fit Guide

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five and RX versions.

Disclaimer

These parts are intended for installation by a qualified armourer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action. This is due to the varying tolerances present in all mass-produced firearms. Although kits fit with no issues in a great majority of pistols, Grayguns is unable to guarantee perfect functionality in every instance. Grayguns does offer installation services for all parts kits we offer.

Sig Sauer factory Safety Lock for P227, P220, P226, P229 9mm, SP2009 9mm, SP2340 .40/357 and P239 models with stainless steel slides. Not for use with carbon steel stamped slide versions.

The P22xCT Classic Standard Trigger adds over-travel adjustability to our original design. Utterly indestructible, the P22xCT Classic Standard is machined from tough steel, carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function.

Our intermediate trigger shape optimizes both SA and DA control for optimal control, and is more comfortable than the factory short trigger it replaces. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

Will not fit SIG Pro, X5 Allround, P225 / P6, P239 or most SAO models. Also will not fit older P220 with 8mm wide trigger.

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

This product was previously referred to as the P-Series Precision Adjustable Intermediate Trigger (P-SAIT).

Sig Sauer factory Support Plate for all standard P series models except P239.

Sig Sauer factory Hammer Stop Pin for P220 and P245 models.

The SIG P-Series Dual Adjustable Straight Trigger is the straight-faced version of our legendary curved P-Series Dual Adjustable Trigger. This trigger includes over travel and pre-travel adjustability. (Adjustable for double action slack and single action over travel.)

The optimized trigger face pressure-wall angle provides for outstanding single action sear release and positive, ultra-fast reset control. The ergonomics provides superior double action leverage and control.

Dual Adjustable Straight Trigger Details

This trigger is machined from tough steel. The trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

The trigger weight is about .83 ounces (23.45 grams)

Fit Guide

The trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including

• X5 All-Round
• P220 (see exceptions below)
• P226
• P228
• P229
• P227 and others

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

Sig Sauer factory Hammer Strut Roll Pin (old style) for all models. Pin installs on the base of the Hammer Strut and retains the Mainspring.

P220 above Serial # 219166

• Models without plastic retainer/base
• Factory Standard 24 LB

Sig P225, P226, P228 and P229

• Factory Standard 24 LB

The Grayguns P-Series Dual Adjustable Curved Trigger is the ultimate trigger upgrade for your Legion Series or any modern DA/SA SIG P-Series pistol.

Bruce Gray has combined the adjustable over-travel feature, unbeatable comfort and control and unrivaled quality of our original OEM SIG Sauer® Legion P22xCT, Classic Standard trigger, with the improved geometry and pre-travel adjustment of our wildly popular P22xST Dual Adjustable Straight Trigger series.

This trigger is the ultimate upgrade for your Legion Series or any modern DA/SA SIG P-Series pistol.

Our Dual Adjustable Curved Trigger

This steel trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. The trigger is guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

Fit Guide

The Dual Adjustable Curved Trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including:

• X5 All-Round
• P220 (see exception below)
• P226
• P228
• P229
• P227, and others.

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-Series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width.

Sig Sauer factory Mainspring (Hammer Spring) for all caliber P239 DAK models and P220 (old style) DA/SA.

Sig Sauer factory sear spring for all classic P series models.

Factory replacement grip panels for your Sig P220 COMPACT.

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P220 and P226 - Stainless

Sig Sauer factory replacement recoil spring for P220 Combat .45ACP.

Sig Sauer Take Down Lever for P220, P225, P226, P228, P229 and P245 models. This Sig Sauer factory part is phosphate coated as found on the P226 Navy and P220 Combat models.