Sig Sauer P226 Gun Parts

Factory Nickel Short Trigger for the Sig P226, P224, P228 and P229 and recent production P220's. A Short Trigger for the P220 SAO is not available. 10mm wide. The SIG SAUER® Short Trigger is for shooters with small hands and was designed to enhance trigger manipulation for better shooting performance.

Sig Sauer SRT Safety Lever for the P226, P228, and P229 series pistols. Will NOT work on P227 series.

Sig Sauer factory Mainspring (Hammer Spring) for all caliber P225, P226, P228, P229 (old style) DA/SA and P239 models.

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P220 and P226 - Super Black Finish

SIG factory outer extractor spring for P Series with new longer external extractor.

Sig Sauer factory Firing Pin Retaining Pin for P227, P220, P226, P229, P229. P224 and P239 stainless steel slide models. This is the spiral or coiled pin found on later model pistols. Not for use on older pistols or those that use the solid FPPP or the 2 piece roll pins. For slides with short extractors only.

Sig Sauer factory Safety Lock Spring for P227, P220, P226, P229 and P239 models with stainless steel slides.

The SIG P-Series Dual Adjustable Straight Trigger is the straight-faced version of our legendary curved P-Series Dual Adjustable Trigger. This trigger includes over travel and pre-travel adjustability. (Adjustable for double action slack and single action over travel.)

The optimized trigger face pressure-wall angle provides for outstanding single action sear release and positive, ultra-fast reset control. The ergonomics provides superior double action leverage and control.

Dual Adjustable Straight Trigger Details

This trigger is machined from tough steel. The trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

The trigger weight is about .83 ounces (23.45 grams)

Fit Guide

The trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including

• X5 All-Round
• P220 (see exceptions below)
• P226
• P228
• P229
• P227 and others

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

Sig Sauer factory replacement recoil spring for the .22LR conversion kits and the 2 Step P series guns with the .22LR slide assembly.

Sig Sauer factory Firing Pin Retaining Pin for P220, P226, P229, P229. P224 and P239 stainless steel slide models. This is the spiral or coiled pin found on newer model pistols with the long extractor. For slides with LONG extractors only.

Sig Sauer factory Hammer Stop for P226/227 models.

Kit Contains:

• Recoil Spring
• Trigger Bar Spring
• Slide Catch Lever Spring
• Decocking Lever Spring
• Firing Pin Position Pin
• (4) Grip Screws

Sig Sauer factory ejector for P226 9mm and P227 .45ACP models.

Sig Sauer factory Mainspring (Hammer Spring) for all caliber P220, P226, and P229 DAK models.

Sig Sauer factory Mainspring (Hammer Spring) for all caliber P227, P220, P226, P228, P229 (new style) and P245 DA/SA models.

Sig Sauer factory pivot pin for all classic P series models.

Sig Sauer factory Trigger Bar for P226/228/229 DAK models.

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P220 and P226 - Stainless