AR-15 CHARGING HANDLES

AR-15 CHARGING HANDLES

Shop by:

Color

Products

15" RG2-S M-LOK Handguard for AR-15, BLK

15" RG2-S M-LOK Handguard for AR-15, BLK

Breek's newly developed RG2-S (Rugged Rail Mod2 Skeletonized) Handguard line up is an evolution from our previous lineup. Our Patent Pending locking mechanism uses a wedge block system that puts equal pressure all the way around the barrel nut. This gives you better harmonics and a much stronger mounting solution especially when you're putting pressure on the end using a bipod or sling.

The Newly Released RG2 handguards were developed specifically for suppressor builds, each length is designed to fit common barrel length and leave room for all types of quick attach suppressor mounting solutions. The skeletonized design shaves as much weight as posssible without sacrificing the integrity of the handguard. All edges are chamfered, blasted, then Type 3 Hardcoat anodized for a smooth feel.

Highlights

  • Patent Pending Rugged Rail System - 2 Piece Wedge Blocks Allow for a Rock Solid Attachment
  • Fits AR-15 & M4 variants (223, 556, 9mm, & 300blk)
  • Fits Mil Spec Forged & Billet Style Uppers
  • Handguard & Wedge Blocks are Made From Aircraft Grade 6061-T6 Aluminum
  • Mil-Spec Type III Class 2 Hard Coat Anodize
  • Large Cutouts Made to Reduce Weight and Provide Ventilation
  • Slim-line, Smooth Handguard Profile
  • Magpul Licensed M-LOK Mounting System
  • Barrel Nut is Made From High Grade Steel & Coated
  • Proudly Made in the USA
  • Comes with our Breek Arms 1 Year Warranty


Advanced Specs

Handguard Length: 15 Inches

Total Weight w/ Barrel Nut: 13.3 Ounces

Barrel Nut Weight: 3.1 Ounces

Cutout Length (from longest point): 0.275 Inches

Inside Diameter (ID): 1.375 Inches

Front Outside Diameter (OD): 1.605 Inches

ID + Top Gas Tube Channel: 1.73 Inches

Gas Tube Channel Width: 0.475 Inches

Gas Block Compatibility: Low profile & adjustable low-profile gas blocks

Barrel Nut Wrench Size: 1 1/4"

Color: Black

Installation Instructions

  1. Torque barrel nut to 40 - 60 ft pounds
  2. Anti-Seize on the barrel nut is not necessary but recommended
  3. Line the handguard top rail to the AR upper receiver rail for a seamless fit
  4. Install wedges and torque two 10/32 bolts to 40 inch pounds

BRK1516

In stock

$129.95

Breek Arms Low Profile .750

Breek Arms Low Profile .750

Low Profile Set Screw style Gas Blocks for the AR-15 or AR-10 are machined with high quality steel and coated with nitride. The low profile gas block design allows you to mount it underneath any free float hand-guard slim or regular sized. It is not milled out so there is a solid uniform surface that will not collect dust and dirt. Standard barrel diameter is 0.750, but there are several other sizes that will work with other barrel diameters.

BRK275

In stock

$25.45

The Sledgehammer AR-15 Gas Blocking Charging Handle

The Sledgehammer AR-15 Gas Blocking Charging Handle

Introducing the NEW Sledgehammer AR-15 Charging Handle by Breek Arms. The Sledgehammer is the ultimate solution for enthusiasts and professionals seeking top-tier performance and unparalleled reliability, especially when shooting suppressed. Crafted with precision, this feature-rich charging handle offers reliable high performance at an approachable price point resulting in unmatched value for shooters.

Built using industry leading aerospace grade 7075-T6 aluminum, the Sledgehammer combines rugged durability with unmatched functionality. The Sledgehammer features robust serrated latches for effortless and secure manipulation as well as a wider footprint for quick, smooth operation in any situation.

With more gas-reducing features than any other charging handle on the market, the Sledgehammer excels at porting gases away from the shooter's face. The unique design elements effectively mitigate excess gas pressure away from the shooter's face, enhancing the shooting experience.

Specs:

-Material: 7075-T6 Aluminum

-Finish: Type III Hard-Coat Anodized

-Weight: 1.1 Oz

-Latch Width: 2.59”

-Fits All Mil Spec AR15/M16 Rifles

-No Gunsmithing Required

-Made in America

Gas Reducing Features

Higher raised shelf at the rear of the upper receiver to block gas from the shooters face
Innovative keyway cutout to prevent gas from flowing over the rear shelf
Internal baffling inside the stem to create turbulence and slow gas expansion
Back pressure port and aggressive relief cuts on the top and bottom to direct gases away from the shooter's face

BRK6015

In stock

$79.95

Aero Precision AR10 .308 Charging Handle

Aero Precision AR10 .308 Charging Handle

Features:

  • Aluminum Alloy Standard Charging Handle
  • Black Anodized
  • Caliber - .308
  • Made in the USA

APRH100125

In stock

$26.99

Aero Precision AR15/M4 5.56 Charging Handle

Aero Precision AR15/M4 5.56 Charging Handle

Features:

  • Aluminum Alloy Standard Charging Handle
  • Black Anodized
  • Caliber - 5.56
  • Made in the USA

APRH100000C

In stock

$24.00

Radian Weapons Raptor AR15/M4 5.56 Ambidextrous Charging Handle - FDE

Radian Weapons Raptor AR15/M4 5.56 Ambidextrous Charging Handle - FDE

The Raptor is truly revolutionary in design & function. From rapid palm blading or finger thumb charges of the weapon, the motion is fluid & fast from either strong or support side. Made in the USA from aircraft grade 7075 aluminum and MILSPEC anodized.


R0003

In stock

$99.95

Timber Creek Enforcer Ambi Charging Handle - BLK

Timber Creek Enforcer Ambi Charging Handle - BLK

The Enforcer Ambidextrous Charging Handle is a drop-in replacement for mil-spec charging handles. Oversized levers allow for easy access and fluid operation no matter what optic is mounted above it. Featuring our Patent Pending Roller Bearing Technology, this charging handle smoothly and effortlessly unlatches when manipulated from either side of the weapon regardless of you dominate hand. CNC machined out of aircraft grade billet aluminum

E-AMBI-CH-BL

In stock

$83.99

9.7" RG2-S M-LOK Handguard for AR-15, BLK

9.7" RG2-S M-LOK Handguard for AR-15, BLK

Breek's newly developed RG2-S (Rugged Rail Mod2 Skeletonized) Handguard line up is an evolution from our previous lineup. Our Patent Pending locking mechanism uses a wedge block system that puts equal pressure all the way around the barrel nut. This gives you better harmonics and a much stronger mounting solution especially when you're putting pressure on the end using a bipod or sling.

The Newly Released RG2 handguards were developed specifically for suppressor builds, each length is designed to fit common barrel length and leave room for all types of quick attach suppressor mounting solutions. The skeletonized design shaves as much weight as posssible without sacrificing the integrity of the handguard. All edges are chamfered, blasted, then Type 3 Hardcoat anodized for a smooth feel.

Highlights

  • Patent Pending Rugged Rail System - 2 Piece Wedge Blocks Allow for a Rock Solid Attachment
  • Fits AR-15 & M4 variants (223, 556, 9mm, & 300blk)
  • Fits Mil Spec Forged & Billet Style Uppers
  • Handguard & Wedge Blocks are Made From Aircraft Grade 6061-T6 Aluminum
  • Mil-Spec Type III Class 2 Hard Coat Anodize
  • Large Cutouts Made to Reduce Weight and Provide Ventilation
  • Slim-line, Smooth Handguard Profile
  • Magpul Licensed M-LOK Mounting System
  • Barrel Nut is Made From High Grade Steel & Coated
  • Proudly Made in the USA
  • Comes with our Breek Arms 1 Year Warranty


Advanced Specs

Handguard Length: 9.7 Inches

Total Weight w/ Barrel Nut: 10.4 Ounces

Barrel Nut Weight: 3.1 Ounces

Cutout Length (from longest point): 0.275 Inches

Inside Diameter (ID): 1.375 Inches

Front Outside Diameter (OD): 1.605 Inches

ID + Top Gas Tube Channel: 1.73 Inches

Gas Tube Channel Width: 0.475 Inches

Gas Block Compatibility: Low profile & adjustable low-profile gas blocks

Barrel Nut Wrench Size: 1 1/4"

Color: Black

Installation Instructions

  1. Torque barrel nut to 40 - 60 ft pounds
  2. Anti-Seize on the barrel nut is not necessary but recommended
  3. Line the handguard top rail to the AR upper receiver rail for a seamless fit
  4. Install wedges and torque two 10/32 bolts to 40 inch pounds

BRK1513

In stock

$104.95

Bravo Company Gunfighter Charging Handle Mod 4B - Medium Latch

Bravo Company Gunfighter Charging Handle Mod 4B - Medium Latch

Charging Handle forged from 7075 T6 Aluminum
Hard Coat Anodized per Mil-A-8625F, Type III, Class 2
The Mod 4B latch extends past the main body of the charging handle by approximately .91".

For comparison a USGI handle latch extended past the main body of the charging handle by approximately .85"

Compatible with Mil-Spec AR-15 Direct Impingement Weapon Systems.

**NOT compatible with adjustable gas keyed bolt carrier groups.**
Driven by over a decade of feedback from real-world combat operations, BCM® has made continual design refinements and structural improvements to the charging handle in the M4 and M16 to address the current manual of arms for the weapon system.
Optimizing the contours into a snag-free profile that facilitates immediate manipulation with an end user’s reaction side grip. The range of BCMGUNFIGHTER™ Charging Handles is available with both ambidextrous and MIL-SPEC controls.
Redesigned to eliminate the load on the pivot pin (like USGI handle fitted with an extended latch) and keep the energy from charging close the centerline of the carbine/rifle, BCMGUNFIGHTER™ Charging Handles provides a larger uninterrupted engagement surface with a smaller silhouette.

BCM-GFH-MOD4B-556

In stock

$74.95

Radian Weapons Raptor LT AR15/M4 5.56 Ambidextrous Charging Handle - Black

Radian Weapons Raptor LT AR15/M4 5.56 Ambidextrous Charging Handle - Black

The Radian Raptor-LT uses the same patented ambidextrous functionality as its predecessor. The Raptor-LT handles are machined from 7075 aluminum, MILSPEC Type III hard anodized, then over-molded with high-strength, fiberglass reinforced polymer for the ultimate combination of strength, weight and durability. Compatible with AR15/M16 or AR10/SR25-pattern rifles. Like all Radian products, the Raptor-LT comes with a limited lifetime warranty, and is 100% designed and manufactured in the USA.


R0148

In stock

$74.95

The Sledgehammer AR-15 Gas Blocking Charging Handle, FDE

The Sledgehammer AR-15 Gas Blocking Charging Handle, FDE

Introducing the NEW Sledgehammer AR-15 Charging Handle by Breek Arms. The Sledgehammer is the ultimate solution for enthusiasts and professionals seeking top-tier performance and unparalleled reliability, especially when shooting suppressed. Crafted with precision, this feature-rich charging handle offers reliable high performance at an approachable price point resulting in unmatched value for shooters.

Built using industry leading aerospace grade 7075-T6 aluminum, the Sledgehammer combines rugged durability with unmatched functionality. The Sledgehammer features robust serrated latches for effortless and secure manipulation as well as a wider footprint for quick, smooth operation in any situation.

With more gas-reducing features than any other charging handle on the market, the Sledgehammer excels at porting gases away from the shooter's face. The unique design elements effectively mitigate excess gas pressure away from the shooter's face, enhancing the shooting experience.

Specs:

-Material: 7075-T6 Aluminum

-Finish: Type III Hard-Coat Anodized

-Weight: 1.1 Oz

-Latch Width: 2.59”

-Fits All Mil Spec AR15/M16 Rifles

-No Gunsmithing Required

-Made in America

Gas Reducing Features

Higher raised shelf at the rear of the upper receiver to block gas from the shooters face
Innovative keyway cutout to prevent gas from flowing over the rear shelf
Internal baffling inside the stem to create turbulence and slow gas expansion
Back pressure port and aggressive relief cuts on the top and bottom to direct gases away from the shooter's face

BRK6015-FDE

In stock

$79.95

Bravo Company Gunfighter Charging Handle Mod 3B - Large Latch

Bravo Company Gunfighter Charging Handle Mod 3B - Large Latch

Charging Handle forged from 7075 T6 Aluminum

Hard Coat Anodized per Mil-A-8625F, Type III, Class 2
The Mod 3B latch extends past the main body of the charging handle by approximately 1.14".
For comparison a USGI handle latch extended past the main body of the charging handle by approximately .85"


Compatible with Mil-Spec AR-15 Direct Impingement Weapon Systems.

**NOT compatible with adjustable gas keyed bolt carrier groups.**
Driven by over a decade of feedback from real-world combat operations, BCM® has made continual design refinements and structural improvements to the charging handle in the M4 and M16 to address the current manual of arms for the weapon system.
Optimizing the contours into a snag-free profile that facilitates immediate manipulation with an end user’s reaction side grip. The range of BCMGUNFIGHTER™ Charging Handles is available with both ambidextrous and MIL-SPEC controls.
Redesigned to eliminate the load on the pivot pin (like USGI handle fitted with an extended latch) and keep the energy from charging close the centerline of the carbine/rifle, BCMGUNFIGHTER™ Charging Handles provides an larger uninterrupted engagement surface with a smaller silhouette.

BCM-GFH-MOD3B-556

In stock

$74.95

Radian Weapons Raptor LT AR15/M4 5.56 Ambidextrous Charging Handle - FDE

Radian Weapons Raptor LT AR15/M4 5.56 Ambidextrous Charging Handle - FDE

The Radian Raptor-LT uses the same patented ambidextrous functionality as its predecessor. The Raptor-LT handles are machined from 7075 aluminum, MILSPEC Type III hard anodized, then over-molded with high-strength, fiberglass reinforced polymer for the ultimate combination of strength, weight and durability. Compatible with AR15/M16 or AR10/SR25-pattern rifles. Like all Radian products, the Raptor-LT comes with a limited lifetime warranty, and is 100% designed and manufactured in the USA.


R0149

In stock

$79.95

13.7" RG2-S M-LOK Handguard for AR-15, BLK

13.7" RG2-S M-LOK Handguard for AR-15, BLK

Breek's newly developed RG2-S (Rugged Rail Mod2 Skeletonized) Handguard line up is an evolution from our previous lineup. Our Patent Pending locking mechanism uses a wedge block system that puts equal pressure all the way around the barrel nut. This gives you better harmonics and a much stronger mounting solution especially when you're putting pressure on the end using a bipod or sling.

The Newly Released RG2 handguards were developed specifically for suppressor builds, each length is designed to fit common barrel length and leave room for all types of quick attach suppressor mounting solutions. The skeletonized design shaves as much weight as posssible without sacrificing the integrity of the handguard. All edges are chamfered, blasted, then Type 3 Hardcoat anodized for a smooth feel.

Highlights

  • Patent Pending Rugged Rail System - 2 Piece Wedge Blocks Allow for a Rock Solid Attachment
  • Fits AR-15 & M4 variants (223, 556, 9mm, & 300blk)
  • Fits Mil Spec Forged & Billet Style Uppers
  • Handguard & Wedge Blocks are Made From Aircraft Grade 6061-T6 Aluminum
  • Mil-Spec Type III Class 2 Hard Coat Anodize
  • Large Cutouts Made to Reduce Weight and Provide Ventilation
  • Slim-line, Smooth Handguard Profile
  • Magpul Licensed M-LOK Mounting System
  • Barrel Nut is Made From High Grade Steel & Coated
  • Proudly Made in the USA
  • Comes with our Breek Arms 1 Year Warranty


Advanced Specs

Handguard Length: 13.7 Inches

Total Weight w/ Barrel Nut: 12.7 Ounces

Barrel Nut Weight: 3.1 Ounces

Cutout Length (from longest point): 0.275 Inches

Inside Diameter (ID): 1.375 Inches

Front Outside Diameter (OD): 1.605 Inches

ID + Top Gas Tube Channel: 1.73 Inches

Gas Tube Channel Width: 0.475 Inches

Gas Block Compatibility: Low profile & adjustable low-profile gas blocks

Barrel Nut Wrench Size: 1 1/4"

Color: Black

Installation Instructions

  1. Torque barrel nut to 40 - 60 ft pounds
  2. Anti-Seize on the barrel nut is not necessary but recommended
  3. Line the handguard top rail to the AR upper receiver rail for a seamless fit
  4. Install wedges and torque two 10/32 bolts to 40 inch pounds

BRK1515

Out of stock

Out of stock
Aero Precision AR10 .308 Breach Ambi Charging Handle - BLK

Aero Precision AR10 .308 Breach Ambi Charging Handle - BLK

The Aero Precision BREACH® is a rugged, ambidextrous, precision-manufactured charging handle for the M5/AR308 platform. The BREACH's design utilizes a reinforced 7075-T6 aluminum bar that is up to the most demanding tasks. Its ambidextrous levers feature a patent-pending, dual spring system, that directs the force-of-use into the robust charging handle body. This allows the shooter to use a one-sided charging technique without compromising the part — a pitfall for traditional charging handles.

The large lever configuration provides an extended operating surface, perfect for a user with bigger hands, or someone who wants a larger surface for manipulation of the charging handle.

NOTE: This charging handle is NOT compatible with Sig Sauer 716, Savage MSR10, or Smith and Wesson M&P10 rifles as they utilize a proprietary design.

FEATURES:

  • Ambidextrous Controls: Ergonomically designed 7075 Aluminum levers allow the user to easily charge their firearm with either hand, while remaining low profile and comfortable when slung.
  • Robust Construction: Reduced chamfer angles on the 7075 Aluminum reinforced bar design provide a strong foundation for the BREACH® that is resistant to rotational flex or breakage.
  • Patent-pending Lever Mechanism: Transfers force-of-use away from the roll pins and into the top/head portion of the reinforced bar protecting the charging handle in the most demanding circumstances.
  • Gas Deflection Shelf: Aligns with the upper receiver to redirect gas flow away from the users face when shooting suppressed.
  • Functional Design: It is not all just good looks. Stylistic cuts on the charging handle also help to clear stuck on carbon and debris from the upper receiver, while the spacer design seals and protects the lever mechanism from debris.

APRA700301C

Out of stock

Out of stock
Aero Precision AR15/M4 5.56 Breach Ambi Charging Handle - BLK

Aero Precision AR15/M4 5.56 Breach Ambi Charging Handle - BLK

The Aero Precision BREACH® is a rugged, ambidextrous, precision-manufactured charging handle for the AR15 platform. The BREACH's design utilizes a reinforced 7075-T6 aluminum bar that is up to the most demanding tasks. Its ambidextrous levers feature a patent-pending, dual spring system, that directs the force-of-use into the robust charging handle body. This allows the shooter to use a one-sided charging technique without compromising the part — a pitfall for traditional mil-spec charging handles.

The small lever configuration provides a low-profile, easily gripped interface that is comfortable when slung and can be actuated effortlessly from either side of your rifle.

  • Ambidextrous Controls: Ergonomically designed 7075 Aluminum levers allow the user to easily charge their firearm with either hand, while remaining low profile and comfortable when slung.
  • Robust Construction: Reduced chamfer angles on the 7075 Aluminum reinforced bar design provide a strong foundation for the BREACH® that is resistant to rotational flex or breakage.
  • Patent-pending Lever Mechanism: Transfers force-of-use away from the roll pins and into the top/head portion of the reinforced bar protecting the charging handle in the most demanding circumstances.
  • Gas Deflection Shelf: Aligns with the upper receiver to redirect gas flow away from the users face when shooting suppressed.
  • Functional Design: It is not all just good looks. Stylistic cuts on the charging handle also help to clear stuck on carbon and debris from the upper receiver, while the spacer design seals and protects the lever mechanism from debris.

APRA700100C

Out of stock

Out of stock
Aero Precision AR15/M4 5.56 Breach Ambi Charging Handle - OD Green

Aero Precision AR15/M4 5.56 Breach Ambi Charging Handle - OD Green

The Aero Precision BREACH® is a rugged, ambidextrous, precision-manufactured charging handle for the AR15 platform. The BREACH's design utilizes a reinforced 7075-T6 aluminum bar that is up to the most demanding tasks. Its ambidextrous levers feature a patent-pending, dual spring system, that directs the force-of-use into the robust charging handle body. This allows the shooter to use a one-sided charging technique without compromising the part — a pitfall for traditional mil-spec charging handles.

The small lever configuration provides a low-profile, easily gripped interface that is comfortable when slung and can be actuated effortlessly from either side of your rifle.

  • Ambidextrous Controls: Ergonomically designed 7075 Aluminum levers allow the user to easily charge their firearm with either hand, while remaining low profile and comfortable when slung.
  • Robust Construction: Reduced chamfer angles on the 7075 Aluminum reinforced bar design provide a strong foundation for the BREACH® that is resistant to rotational flex or breakage.
  • Patent-pending Lever Mechanism: Transfers force-of-use away from the roll pins and into the top/head portion of the reinforced bar protecting the charging handle in the most demanding circumstances.
  • Gas Deflection Shelf: Aligns with the upper receiver to redirect gas flow away from the users face when shooting suppressed.
  • Functional Design: It is not all just good looks. Stylistic cuts on the charging handle also help to clear stuck on carbon and debris from the upper receiver, while the spacer design seals and protects the lever mechanism from debris.

APRA700130C

Out of stock

Out of stock
Aero Precision AR15/M4 5.56 Breach Ambi Charging Handle - TAN

Aero Precision AR15/M4 5.56 Breach Ambi Charging Handle - TAN

The Aero Precision BREACH® is a rugged, ambidextrous, precision-manufactured charging handle for the AR15 platform. The BREACH's design utilizes a reinforced 7075-T6 aluminum bar that is up to the most demanding tasks. Its ambidextrous levers feature a patent-pending, dual spring system, that directs the force-of-use into the robust charging handle body. This allows the shooter to use a one-sided charging technique without compromising the part — a pitfall for traditional mil-spec charging handles.

The small lever configuration provides a low-profile, easily gripped interface that is comfortable when slung and can be actuated effortlessly from either side of your rifle.

  • Ambidextrous Controls: Ergonomically designed 7075 Aluminum levers allow the user to easily charge their firearm with either hand, while remaining low profile and comfortable when slung.
  • Robust Construction: Reduced chamfer angles on the 7075 Aluminum reinforced bar design provide a strong foundation for the BREACH® that is resistant to rotational flex or breakage.
  • Patent-pending Lever Mechanism: Transfers force-of-use away from the roll pins and into the top/head portion of the reinforced bar protecting the charging handle in the most demanding circumstances.
  • Gas Deflection Shelf: Aligns with the upper receiver to redirect gas flow away from the users face when shooting suppressed.
  • Functional Design: It is not all just good looks. Stylistic cuts on the charging handle also help to clear stuck on carbon and debris from the upper receiver, while the spacer design seals and protects the lever mechanism from debris.

APRA700120C

Out of stock

Out of stock