Sig Sauer P229 Gun Parts

SIG factory Nickel Take Down Lever for P220, P225, P226, P228, P229 and P245 models. Replaces part #34229065N

Sig Sauer factory Hammer Strut Roll Pin (old style) for all models. Pin installs on the base of the Hammer Strut and retains the Mainspring.

Sig Sauer factory Trigger Pivot Pin for P225, P226, P228 and P229 models.

Sig Sauer factory Decocking Lever for P227, P226, P228 and P229 models. Phosphate finish.

Wolff Hammer Spring for the Sig P220/P227/P226/P229 that use the black plastic mainspring seat. (Short Spring)

• Later Model Design
• Factory Standard 21LB
• Reduced Power 17LB, 18LB, & 19LB

Sig Sauer factory sear spring for all classic P series models.

The SIG P-Series Dual Adjustable Straight Trigger is the straight-faced version of our legendary curved P-Series Dual Adjustable Trigger. This trigger includes over travel and pre-travel adjustability. (Adjustable for double action slack and single action over travel.)

The optimized trigger face pressure-wall angle provides for outstanding single action sear release and positive, ultra-fast reset control. The ergonomics provides superior double action leverage and control.

Dual Adjustable Straight Trigger Details

This trigger is machined from tough steel. The trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

The trigger weight is about .83 ounces (23.45 grams)

Fit Guide

The trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including

• X5 All-Round
• P220 (see exceptions below)
• P226
• P228
• P229
• P227 and others

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

SIG factory inner extractor spring for P Series with new longer external extractor.

SIG factory outer extractor spring for P Series with new longer external extractor.

Developed by the renowned gunsmiths of Grayguns, the FAT guide rods are designed to optimally support factory Sig Sauer, and Grayguns custom multi-strand springs for maximum service life and smooth, reliable function. Designed to the maximum nominal diameter to fit each pistol perfectly, FAT rods also eliminate the possibility of coil-jumping and damage when used with correctly-selected after-market single strand recoil springs. Grayguns FAT rods are hardened and stress-relieved to withstand a lifetime of hard use as well as being carefully polished stainless or finished in ultra-durable Super Black. Lifetime guarantee against galling, ringing or breakage. Simply put, some of the highest quality guide rods available today.

Fits Sig Sauer P228 and P229 - Stainless

The P22xCT Classic Standard Trigger adds over-travel adjustability to our original design. Utterly indestructible, the P22xCT Classic Standard is machined from tough steel, carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function.

Our intermediate trigger shape optimizes both SA and DA control for optimal control, and is more comfortable than the factory short trigger it replaces. Guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

Will not fit SIG Pro, X5 Allround, P225 / P6, P239 or most SAO models. Also will not fit older P220 with 8mm wide trigger.

Intended to be installed by a qualified Sig Sauer armorer or gunsmith

This product was previously referred to as the P-Series Precision Adjustable Intermediate Trigger (P-SAIT).

Sig Sauer factory Safety Lock for P229 .40S&W and P229 .357SIG.

Bruce Gray combined the best of both worlds when he designed what we know as the hybrid trigger.

The unique face allows the shooter can take advantage of finger placement lower on the face, with the comfort of a traditional curved face. This hybrid design reduces trigger weight while preserving all mechanical safety values.

The Grayguns P320 Hybrid Trigger uses internal leverage changes to yield superior trigger pull, while supporting the voluntary upgrade’s enhanced reliability and rough handling performance qualities.

Includes our adjustable over-travel stop design to shorten reset and take out all gross over-travel. Designed for easy drop-in installation.

Specifically designed for P320s with current fire control unit components, or those who have gone through SIG’s Voluntary Upgrade Program.

Specifications and Features

• Specifically designed for P320s with current fire control unit components, or those who have gone through SIG’s Voluntary Upgrade Program
• Adjustable over-travel to help reduce reset and take out wasted motion
• Reduces total trigger pull weight approximately 2 pounds below factory-stock for the standard series, and about 1.25 pounds for the X-Five variant
• Designed for use with the SIG factory trigger bar spring
• Minimal over-travel, stops at optimum trigger face angle
• Smoother takeup and release sensation
• Preserves factory sear engagement and mechanical safety values
• Proven reliable and durable for high-volume professional use
• Limited lifetime warranty on materials and workmanship

Fit Guide

Fits all variations within the P320 (upgraded) system. Including all sizes, TACOPS Carry, X-VTAC, X-Carry, X-Five and RX versions.

Disclaimer

These parts are intended for installation by a qualified armourer or gunsmith. In some cases professional fitting will be required by a trained, qualified armorer/gunsmith who is very familiar with the pistol’s action. This is due to the varying tolerances present in all mass-produced firearms. Although kits fit with no issues in a great majority of pistols, Grayguns is unable to guarantee perfect functionality in every instance. Grayguns does offer installation services for all parts kits we offer.

SIG P225/228/229 RECOIL SPRINGS

• Factory Standard 9mm, .40 S&W: 16LB
• Factory Standard 357 Sig : 17LB

*Firing Pin Spring Included

Sig Sauer factory Mainspring (Hammer Spring) for all caliber P220, P226, and P229 DAK models.

P220 above Serial # 219166

• Models without plastic retainer/base
• Factory Standard 24 LB

Sig P225, P226, P228 and P229

• Factory Standard 24 LB

Sig Sauer factory Safety Lever for P225, P226, P228, P229 and P239 models.

The Grayguns P-Series Dual Adjustable Curved Trigger is the ultimate trigger upgrade for your Legion Series or any modern DA/SA SIG P-Series pistol.

Bruce Gray has combined the adjustable over-travel feature, unbeatable comfort and control and unrivaled quality of our original OEM SIG Sauer® Legion P22xCT, Classic Standard trigger, with the improved geometry and pre-travel adjustment of our wildly popular P22xST Dual Adjustable Straight Trigger series.

This trigger is the ultimate upgrade for your Legion Series or any modern DA/SA SIG P-Series pistol.

Our Dual Adjustable Curved Trigger

This steel trigger is carefully heat treated and finished in black oxide. Tight pin hole tolerances assure smooth, solid function. The trigger is guaranteed for life against defects in materials or workmanship.

Made with love, supplied with a hex key.

Fit Guide

The Dual Adjustable Curved Trigger is designed to fit both current and older model traditional double action (DA/SA/decocker) P-Series pistols, including:

• X5 All-Round
• P220 (see exception below)
• P226
• P228
• P229
• P227, and others.

These triggers are approximately 10mm wide. At this time, we are not suggesting this trigger for guns equipped with the DAK trigger system.

This trigger may not be fully compatible with California compliant or similar P-Series pistol models equipped with a magazine disconnector, and Grayguns urges caution. We do not recommend deactivating any mechanical safety device.

The Grayguns DA/SA triggers will not fit SIG Pro, P225 / P6, P239, West German P220s, or most SAO models. Most of these triggers are a narrower 8mm width.