ARMORER'S TOOLS
CED 1911 Tool Kit
SKU: CED1911KIT
-
5/32" Pin Punch Remove and install the firing pin. Remove and install the Mainspring housing retaining pin. Remove the hammer axis pin. Remove Magazine base pads
-
Small Screwdriver .150" Remove and install the magazine catch. Some sight adjusting screws such as the windage screw on the Gold Cup rear sight.
-
Medium Screwdriver .210" Fits the adjusting screws on most rear sights including Bo-mar, LPA, Millett, and Gold Cup
-
Large Screwdriver .325" For grip screws. Note: We found that there were two distinct widths of grip screws on the market. Some have slots around .039" wide, while others .050". Unfortunately, we could not accommodate both with a perfectly sized blade, so we have used the smaller size.
-
3/32" Hex Drive Fits most extension buttons screwed onto magazine catches and aftermarket grip screws with hex heads. Can also be used to push out the sear axis pin and depressing the detent to fit the safety catch.
-
5/32" Hex Drive Fits several brands of two piece recoil spring guide rods.
$19.95
Cup Tip Punch - 3mm (2 punch set)
SKU: CTP3MM-SET
Each punch is machined from one solid piece of steel bar stock to our specifications. The tip is concave to prevent flattening of the rounded head firing pin positioning pins on SIG stainless steel slides. The shaft is slightly undersized to to allow clearance on the pin hole in the slide. Manufactured by Top Gun Supply in the U.S.A.
Each set comes with 1 short starter punch and 1 longer finishing punch.
$23.95
In Stock
SIG Armorer's Combo Tool
SKU: 99240105
A Multipurpose tool for Sig Sauer handguns featuring a correctly shaped screwdriver tip for removing grip screws, installation and removal of magazine catch and sear spring and a tip to aid in mainspring removal and installation. 5/16" drive. The screwdriver may not fit the older style P226 screws with the smaller .115" shank.$29.95
In Stock
Combo Bit Set - 3 Bits
SKU: WT1832ip20
Combination Bit set for many common grip grip screws. Includes 3/32" Hex Bit, 1/8" Hex Bit and IP20 Torx Plus Bit. Standard 1/4" drive. Made in Germany.$5.29
In Stock
Hex Head Bit - 1/8"
SKU: WT71336
1/8" Hex Head Bit for installing and removing grip screws. Fits SIG P220, P230, P245 and P225 Hogue grip screws along with various other grip screws. Standard 1/4" drive. Made in Germany.$1.79
In Stock
Hex Head Bit - 3/32"
SKU: WT71330
3/32" hex Head Bit for installing and removing grip screws. Fits SIG P226, P228, P229 and P239 Hogue grip screws along with Wilson Combat 1911 and various other grip screws. Standard 1/4" drive. Made in Germany.$1.79
In Stock
Torx Plus Bit - IP20
SKU: WT71620
IP20 Torx Plus for installing and removing SIG factory P229 Torx Plus grip screws. Standard 1/4" drive. Made in Germany.$1.95
In Stock
Hoppe's Bore Light
SKU: BOABRL1
A useful tool for inspection under any conditions. Illuminates the bore fully, so nicks, scratches, pits and fouling can be seen easily. Good for safety checks and for lighting hard-to-get-at areas. Locking feature can lock light on for longer inspections. A good tool to take along if you're buying a used firearm. Uses two AAA Batteries (Not Included)$6.95
In Stock
Sight adjust/install tool - SIG SAUER
SKU: MGWSIG
The MGW SIG sight tool is for use on all models except the P230, P232, P250 and SIGPRO. Will install, remove and adjust many different sights on your Sig Sauer pistol. May not work on some of the wider and taller sights including Tru-Glo and adjustable types. Gunsmith installation is recommended.$115.95

Cart is empty















