ARMORER HAND TOOLS

ARMORER HAND TOOLS

Products

Ghost Clear Armorers Plate - Glock GEN 1-4

Ghost Clear Armorers Plate - Glock GEN 1-4

The Ghost Clear Armorers Plate is a recommended must for trouble free installation of the EVO ELITE, ROCKET & TACTICAL trigger control connectors. Slightly wider than the factory Glock plate to permit moving the firing pin leg slightly forward to give you more adjustment of the trigger control tab once the thinner backplate is reinstalled. The plate is sectioned by 1/3 in height to permit viewing of the sear and firing pin engagement.

GHO-GAP

In stock

$3.79

Glock Armorer's Bench Mat

Glock Armorer's Bench Mat

This padded bench mat is perfect for working on your pistols. The padding helps protect your finish and keep your work in place. Measures 17" X 10 3/4" in size and has worldwide Glock contact information as well as a G17 exploded drawing and parts list.

OAD00062

In stock

$14.95

Wheeler Engineering Delta Series AR Pivot Pin/Roll Pin Install Tool

Wheeler Engineering Delta Series AR Pivot Pin/Roll Pin Install Tool

Wheeler Delta Series AR Pivot Pin Install Tool For the AR-15. Makes pivot spring and detent work fast and effortless. Roll Pin Punch and starter for all lower receiver roll pins. Comes with handy key ring for storage. Black zinc plated steel.

156243

In stock

$6.29

Wheeler Engineering Universal Barrel Clamp

Wheeler Engineering Universal Barrel Clamp

Made from aircraft grade aluminum and bonded with non-marring urethane, the Wheeler Universal Barrel Clamp is able to accommodate three different barrel openings of .85”, .66” and .53” allowing you to change anything from a pencil AR barrel to a bull barrel. When inserted in a vise the urethane coating squeezes down tightly on the barrel to fully secure it for the forces needed for installation/ removal.

672286

In stock

$36.95

Wheeler Engineering Nylon/Brass Hammer

Wheeler Engineering Nylon/Brass Hammer

Features both a 1" brass face for driving pins and punches and a non-marring 1" nylon face that is great for pin alignment and other uses where a steel hammer is not appropriate. 11" overall length.

711016

In stock

$17.95

All In One Tool - Ruger Mark I, II, III, 22/45

All In One Tool - Ruger Mark I, II, III, 22/45

All in one takedown tool for the Ruger Mark Series Pistols. The ever popular Ruger Mark Series, known to be cumbersome to disassemble, are some of the most popular .22 caliber pistols on the market. With the All In One Tool, no longer will you avoid cleaning your pistol. This tool allows you to perform full maintenance on your Ruger Mark I, II, III, and 22/45 Series pistols without any modifications to the gun! Also functions as a magazine loader!

RUGER-TOOL

In stock

$21.95

All In One Tool W/Stand - Ruger Mark I, II, III, 22/45

All In One Tool W/Stand - Ruger Mark I, II, III, 22/45

All in one takedown tool for the Ruger Mark Series Pistols. The ever popular Ruger Mark Series, known to be cumbersome to disassemble, are some of the most popular .22 caliber pistols on the market. With the All In One Tool, no longer will you avoid cleaning your pistol. This tool allows you to perform full maintenance on your Ruger Mark I, II, III, and 22/45 Series pistols without any modifications to the gun! Also functions as a magazine loader! Comes with easy to follow step by step instructions as well as a stand for holding your pistol during disassembly.

RUGER-TOOL-S

In stock

$27.95

Lockdown Silica Gel Desiccant Dehumidifier - 750 Gram

Lockdown Silica Gel Desiccant Dehumidifier - 750 Gram

Lockdown Silica Gel Desiccant absorbs moisture from the air inside any safe, vault, or storage area to prevent condensation, mildew, and rust from damaging your firearms. Crystals change color once fully saturated and can easily be recharged in the oven. Non-toxic. Protection for up to 57 cubic feet.

222178

In stock

$14.29

Wheeler Engineering Delta Series AR-15 Armorer's Bench Block

Wheeler Engineering Delta Series AR-15 Armorer's Bench Block

The Wheeler Engineering AR-15 Bench Block is ideal for securing your AR during assembly and disassembly. Made of non-marring urethane, it features various notches, grooves, and holes on both sides for the upper receiver, lower receiver, front sight and charging handle. The perfect tool for your next AR-15 build! Ideal for changing or adjusting triggers, removing or installing pins, detents, and springs. Works with ambidextrous safety lower receivers.

156945

In stock

$34.95

Frankford Arsenal Stainless Steel Dial Caliper - 6"

Frankford Arsenal Stainless Steel Dial Caliper - 6"

The Frankford Arsenal Stainless Steel Dial Caliper is a necessary tool for the precise measurements required for reloading ammunition.

Features:

  1. Accurate to within .001"
  2. 0-6" measurement range
  3. Heavy duty protective case
  4. Locking adjustment
  5. Measure external, internal, and depth
  6. Thumb dial for precise adjustments
  7. Precision milled and ground surfaces for precise accuracy

516503

In stock

$28.95

Glock Front Sight Tool - FACTORY TOOL

Glock Front Sight Tool - FACTORY TOOL

3/16" Hex Nut Tool made by Glock for front sight removal and installation. The handle provides a positive grip to easily remove or install your sights. Not for long slide models. Gunsmith installation is recommended.

SP05686

In stock

$39.99

AR-15 Lower Receiver Vise Block

AR-15 Lower Receiver Vise Block

The Brownells high density urethane vice block inserts into the lower receiver magazine well and locks into place, providing a secure clamping surface. Allows you to safely work on your rifle without the risk of crushing or damaging your lower receiver.

702-004-015

Out of stock

$49.95

Out of stock
Armorer's Punch Set - 14 PIECE

Armorer's Punch Set - 14 PIECE

This 14 piece punch set include two hammers, one nylon and one brass, as well as 12 punches.
  • 8 brass punches from 1/8" to 5/16"
  • 2 Delrin punches - 15/64" and 3/8"
  • 2 steel punches - 3/32" and 7/64"

TL-PHK

Out of stock

$39.95

Out of stock
Beckham Design Ultimate 1911 Barrel Bushing Wrench

Beckham Design Ultimate 1911 Barrel Bushing Wrench

Durable polymer construction, the Beckham Design 1911 Barrel Bushing Wrench fits Government and Commander sized bushings. Shaped identical to a 1911 magazine which allows for easy storage in the mag-well or spare mag holder.

NW244

Out of stock

$8.00

Out of stock
Cup Tip Punch

Cup Tip Punch

Machined from one solid piece of steel bar stock to our specifications. The tip is concave to prevent flattening of the rounded head firing pin positioning pins on SIG stainless steel slides. The shaft is slightly undersized to to allow clearance on the pin hole in the slide. Manufactured by Top Gun Supply in the U.S.A.

CTP-PUNCH

Out of stock

$7.95

Out of stock
Daniel Defense Bolt-Up System Barrel Nut Wrench

Daniel Defense Bolt-Up System Barrel Nut Wrench

The Daniel Defense Bolt-Up Barrel Nut Wrench is a proprietary spanner wrench used to install Daniel Defense AR15 Lite Rail, Omega X, and RIS II Rail System. This wrench is designed to be used with a 1/2 drive torque wrench.

16-002-08234

Out of stock

$10.95

Out of stock
DPMS AR-15 Multi Tool

DPMS AR-15 Multi Tool

The DPMS Multi-Tool is used for installation and disassembly of Free Float Tubes, Barrel Nuts, Compensators, Barrel Extension Tubes and Carbine Stocks. Provides a 1/2" drive for a socket wrench and has a screw driver tip for the buttstock screw. Powder coated steel.

TL-MW

Out of stock

$33.95

Out of stock
Glock Disassembly Tool

Glock Disassembly Tool

Glock Factory Armorer's Tool used in disassembly of Glock Pistols.

GT03374

Out of stock

$7.95

Out of stock

Armorer Tools

Gunsmiths and armorers – time away from the workshop is well spent if you’re shopping our site, because we’ve got the tools to make tasks easier! Start off or expand your collection of armorer tools with a multi-piece armorer’s punch set that includes hammers, as well as steel, brass and delrin punches. Purchase handy pin and roll pin punches in smaller sets. If you’ve got a Glock gun, take a look at the factory armorer’s tool used to disassemble Glock pistols. In addition, we stock an assortment of Glock parts too. A padded bench mat creates the perfect protective place to work on handguns. Once your workspace is covered, use a multipurpose, combination armorer tool for Sig Sauer handguns. It’s got the right screwdriver tips for everything Sig Sauer gunsmiths may need from taking out grip screws to installing a mainspring.

Gunsmithing Tools Equal Repairs Done Right

If you work on guns, you know the right gunsmithing tools make a world of difference! The 1911 versatile tool from Wilson Combat is a gunsmithing tool value; it’s actually an array of tools in one compact unit. Disassemble and assemble a 1911 automatic pistol with this tool. We’ve also got calipers and bits, plus a combination bit set that works on those common grip screws. Safeguard AR-15 rifles while working on them with lower receiver vice blocks and upper receiver action blocks. Keep a multi-use AR-15 tool nearby to assist you. A comprehensive 1911 tool kit supports pistol work that requires pin punch, hex drives and a variety of screwdriver sizes. For rounding out your tool kits, also take a minute to see our sight installation tools.